Business Minor Uiuc, Torque Safe Company Net Worth, Tribunal Lay Member Vacancies, What Happened To Dijonnaise, Articles C

For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). Packaging Authorizations (Column 8) Tanks containing solidified methacrylic acid must not be reheated during transport. No outage is required for helium. An installed inflation cylinder that requires recharging must be filled in accordance with 173.301(l). (2) An indication of compliance with this special provision must be provided by marking each package with the words not restricted or by including the words not restricted on a transport document such as an air waybill accompanying the shipment. Transport vehicles must be vented to prevent accumulation of vapors at a poisonous or flammable concentration. Net weight of contents in wooden boxes, barrels or kegs may not exceed 45 kg (99 pounds). You can When column 7 of the 172.101 table refers to a special provision for a hazardous material, the meaning and requirements of that provision are as set forth in this section. The HMT consists of 10 columns and provides information for each hazardous material listed. Only Specifications MC 304, MC 307 or DOT 407 cargo tank motor vehicles are authorized for transportation by vessel. b. Lithium batteries conforming to paragraph a. of this special provision must be assigned to UN Nos. IBCs are only authorized if approved by the Associate Administrator. 151 If this material meets the definition of a flammable liquid in 173.120 of this subchapter, a FLAMMABLE LIQUID label is also required and the basic description on the shipping paper must indicate the Class 3 subsidiary hazard. IBCs must have a device to allow venting. Transportation of these packages also requires the door of each van trailer to be marked with Warning trailer may contain chemical vapor. ); and. Each tank car must have a reclosing pressure relief device having a start-to-discharge pressure of 15.51 Bar (225 psig). 129 These materials may not be classified and transported unless authorized by the Associate Administrator on the basis of results from Series 2 Test and a Series 6(c) Test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport. A61 a. These notes are explained at the end of each TABLE. TP6 The tank must be equipped with a pressure release device which prevent a tank from bursting under fire engulfment conditions (the conditions prescribed in CGA pamphlet S-1.2 (see 171.7 of this subchapter) or alternative conditions approved by the Associate Administrator may be used to consider the fire engulfment condition), taking into account the properties of the hazardous material to be transported. (vi) Except when an organic peroxide is authorized under 173.225(g), if a hazardous material is not assigned a portable tank T Code, the hazardous material may not be transported in a portable tank unless approved by the Associate Administrator. B54 Open-top, sift-proof rail cars are also authorized. B46 The detachable protective housing for the loading and unloading valves of multi-unit tank car tanks must withstand tank test pressure and must be approved by the Associate Administrator. B68 Sodium must be in a molten condition when loaded and allowed to solidify before shipment. N45 Copper cartridges are authorized as inner packagings if the hazardous material is not in dispersion. When portable tank instruction T75 is referenced in Column (7) of the 172.101 Table, the applicable refrigerated liquefied gases are authorized to be transported in portable tanks in accordance with the requirements of 178.277 of this subchapter. The manufacturer must provide such information to a representative of the Department upon request. Columns 8A, 8B and 8C specify the applicable sections for . TP28 A portable tank having a minimum test pressure of 2.65 bar (265 kPa) may be used provided the calculated test pressure is 2.65 bar or less based on the MAWP of the hazardous material, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. B81 Venting and pressure relief devices for tank car tanks and cargo tanks must be approved by the Associate Administrator. TP16 The portable tank must be protected against over and under pressurization which may be experienced during transportation. Overcharge of the rechargeable lithium ion cells is precluded by design; iii. 177 Gasoline, or, ethanol and gasoline mixtures, for use in internal combustion engines (e.g., in automobiles, stationary engines and other engines) must be assigned to Packing Group II regardless of variations in volatility. 109 Rocket motors must be nonpropulsive in transportation unless approved in accordance with 173.56 of this subchapter. TP32 Portable tanks may be used subject to the following conditions: a. (9) A code containing the letter W refers to a special provision that applies only to transportation by water. 106 The recognized name of the particular explosive may be specified in addition to the type. Lithium batteries installed in a cargo transport unit, designed only to provide power external to the transport unit must use the proper shipping name Lithium batteries installed in cargo transport unit found in the 172.101 Hazardous Materials Table. 50 Cases, cartridge, empty with primer which are made of metallic or plastic casings and meeting the classification criteria of Division 1.4 are not regulated for domestic transportation. d. The proper shipping name Printing ink related material may be used for consignments of packages containing Printing ink and Printing ink related material in the same package. B134 For Large Packagings offered for transport by vessel, flexible or fibre inner packagings shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. 1 CFR 1.1 b. The batteries inside the cargo transport unit are not subject to marking or labelling requirements of part 172 subparts D and E of this subchapter. 164 Substances must not be transported under this entry unless approved by the Associate Administrator on the basis of the results of appropriate tests according to Part I of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). Components classed as Division 6.1, Packing Group I, or Class 8, Packing Group I, must not be offered for transportation and transported under this description. Organization and Purpose Testing must be performed or witnessed by a person who is approved by the Associate Administrator (see 173.56(b) of this subchapter). 155 Fish meal, fish scrap and krill meal may not be transported if the temperature at the time of loading either exceeds 35 C (95 F), or exceeds 5 C (41 F) above the ambient temperature, whichever is higher. Net weight of contents may not exceed 15 kg (33 pounds). Prohibited means bottom openings are prohibited, and Prohibited for liquids means bottom openings are authorized for solid material only. Each portable tank constructed of metal must be fitted with a pressure-relief device consisting of a reclosing spring loaded type, a frangible disc or a fusible element. The Associate Administrator will base the authorization on results from Series 2 tests and a Series 6(c) test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport in accordance with the requirements of this subchapter. N12 Plastic packagings are not authorized. (b) Preparation for transport. here. These special provisions are in addition to the standard packaging requirements. The manufacturer must produce technical documentation of the design type, manufacture as well as the tests and their results. Lighter refills offered for transportation under this entry may not exceed 4 fluid ounces capacity (7.22 cubic inches) or contain more than 65 grams of fuel. (7) Special Provisions (172.102) IB8, IP2, IP4 IBCs are authorized subject to the conditions and limitations of this section provided the IBC type is authorized according to the IBC packaging code specified for the specific hazardous material in Column (7) of the 172.101 Table of this subchapter and the IBC conforms to the requirements in subpart O of part 178 of this subchapter at the . c. The completed package must meet the Packing Group II performance level, as applicable for combination packagings with a plastic box outer packaging, in accordance with subpart M of part 178 of this subchapter. Except for transportation by aircraft, in palletized loads, a pallet box or unit load device (e.g. The letter codes are placed in front of the number codes (for example, "A29"). Amdt. 346 Nitrogen, refrigerated liquid (cryogenic liquid), UN1977 transported in accordance with the requirements for open cryogenic receptacles in 173.320 and this special provision are not subject to any other requirements of this subchapter. Alternatively, the item itself may be used as a packaging if it meets the general packaging requirements of subparts A and B of part 173 of this subchapter. "Published Edition". Shipments made in accordance with this Special provision are excepted from the requirements of 173.60(b)(4) of this subchapter. Each reference in this column to a material which is a hazardous waste or a hazardous substance, and whose proper shipping name is preceded in Column 1 of the Table by the letter "A" or "W", is modified to include " 173.203" or " 173.213", as appropriate for liquids and solids, respectively, on those occasions when the . A56 Radioactive material with a subsidiary hazard of Division 4.2, Packing Group I, must be transported in Type B packages when offered for transportation by aircraft. Those "other methods" for determining authorized packaging are identified at 173.24 (c) (1) (ii). Note 1: Based on maximum lading pressure of 1 psig at top of cargo tank. They must be classified in accordance with the procedure as set out in the Manual of Tests and Criteria, part III, section 39 (IBR, see 171.7 of this subchapter). Wooden boxes must be completely lined with a suitable material impervious to water and nitroglycerin. B70 If DOT 103ANW tank car tank is used: All cast metal in contact with the lading must have 96.7 percent nickel content; and the lading must be anhydrous and free from any impurities. IBCs must be packed in closed freight containers or a closed transport vehicle. Enhanced content is provided to the user to provide additional context. 340 This entry applies only to the vessel transportation of nickel-metal hydride batteries as cargo. Unfortunately, the amendments to the table entries for various hazardous materials introduced new unintended errors that PHMSA is correcting in this notice. A210 This substance is forbidden for transport by air. c. The motor carrier must maintain a satisfactory safety rating as prescribed in 49 CFR part 385. Each transport unit must be leakproof when used as bulk packaging. Special provisions contain packaging provisions, prohibitions, exceptions from requirements for particular quantities or forms of materials and requirements or prohibitions applicable to specific modes of transportation, as follows: (1) A code consisting only of numbers (for example, 11) is multi-modal in application and may apply to bulk and non-bulk packagings. These packagings are not required to: (1.) Have accident damage protection which conforms with 178.345-8 of this subchapter; c. Have a MAWP or design pressure of at least 87 psig: and. shipping name in Column (1) of the 172.101 Table, it means that the mate-rial is known to pose a risk to humans. B78 Tank cars must have a test pressure of 4.14 Bar (60 psig) or greater and conform to Class 103, 104, 105, 109, 111, 112, 114 or 120. (iv) T75. (3) Damage to terminals. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 6.35 mm (0.250 inch) or the thickness required for a tank with a design pressure at least equal to 1.3 times the vapor pressure of the lading at 46 C (115 F). B85 Cargo tanks must be marked with the name of the lading in accordance with the requirements of 172.302(b). In addition, packages shall be legibly and durably marked with an identification of the consignor, the consignee, or both. site when drafting amendatory language for Federal regulations: 23 This material may be transported under the provisions of Division 4.1 only if it is so packed that the percentage of diluent will not fall below that stated in the shipping description at any time during transport. The material is packaged in a DOT Specification 4BW240 cylinder, or in a DOT-51 portable tank. (2) A codes. These provisions are multi-modal and apply to bulk and non-bulk packagings: 1 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone A (see 173.116(a) or 173.133(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. These special provisions are in addition to the standard packaging requirements. 39 This substance may be carried under provisions other than those of Class 1 only if it is so packed that the percentage of water will not fall below that stated at any time during transport. TP33 The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. The chemical under pressure must be classed based on the hazard characteristics of the components in the propellant; the liquid; or the solid. N34 Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material. Packaging must be UN standard metal drums attached with heavy duty steel strapping to a pallet; and. Lead compounds that have a solubility of 5% or less in accordance with this special provision are not subject to the requirements of this subchapter that pertain to Marine Pollutants. Column 7 specifies codes for special provisions applicable to hazardous materials. N85 Packagings certified at the Packing Group I performance level may not be used. Thickness of stainless steel for portable tank shells and heads must be the greater of 6.35 mm (0.250 inch) or the thickness required for a portable tank with a design pressure at least equal to 1.3 times the vapor pressure of the hazardous material at 46 C (115 F). Note also that this exception does not apply to batteries that have been reconditioned for reuse. For UN identification numbers 1327, 1363, 1364, 1365, 1386, 1408, 1841, 2211, 2217, 2793 and 3314, IBCs are not required to meet the IBC performance tests specified in part 178, subpart N, of this subchapter. 156 Asbestos that is immersed or fixed in a natural or artificial binder material, such as cement, plastic, asphalt, resins or mineral ore, or contained in manufactured products is not subject to the requirements of this subchapter. Size of marking on bulk package must conform to 172.302(b) of this subchapter. 132 This description may only be used for ammonium nitrate-based compound fertilizers. 34 The commercial grade of calcium nitrate fertilizer, when consisting mainly of a double salt (calcium nitrate and ammonium nitrate) containing not more than 10 percent ammonium nitrate and at least 12 percent water of crystallization, is not subject to the requirements of this subchapter. per pound of hydrogen peroxide solution. A54 Irrespective of the quantity limits in Column 9B of the 172.101 table, a lithium battery, including a lithium battery packed with, or contained in, equipment that otherwise meets the applicable requirements of 173.185, may have a mass exceeding 35 kg if approved by the Associate Administrator prior to shipment. (3) The total amount of gas from all detectors per outer packaging must not exceed 52 grams (1.83 ounces). 145 This entry applies to formulations that neither detonate in the cavitated state nor deflagrate in laboratory testing, show no effect when heated under confinement, exhibit no explosive power, and are thermally stable (self-accelerating decomposition temperature (SADT) at 60 C (140 F) or higher for a 50 kg (110.2 lbs.) The articles may be transported as in Division 1.4 Compatibility Group D (1.4D) if all of the conditions specified in 173.63(a) of this subchapter are met. (i) Tests must be performed on each type and size of bottle, for each manufacturing location. A20 Plastic bags as inner receptacles of combination packagings are not authorized for transportation by aircraft. B66 Each tank must be equipped with gas tight valve protection caps. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. Packages containing mixtures with not less than 90% by mass, of phlegmatizer need not bear a POISON subsidiary risk label. B48 Portable tanks in sodium metal service may be visually inspected at least once every 5 years instead of being retested hydrostatically. This entry also applies to articles not conforming to the requirements of 173.302, 173.304, or 173.306 of this subchapter, containing a small pressure receptacle with a release device. Each tank must be equipped with pressure relief devices conforming to the following requirements: 1 Total venting capacity in standard cubic feet hour (S.C.F.H.) TP12 This material is considered highly corrosive to steel. TP26 The heating device must be exterior to the shell. The rechargeable (and some non-rechargeable) types have gelled alkaline electrolytes (rather than acidic) making it difficult for them to generate hydrogen or oxygen when overcharged and therefore, differentiating them from non-spillable batteries. b. (2) They must be packed in strong outer packagings and the completed package must be capable of withstanding a 1.8 meter (5.9 feet) drop without leakage of gas contents from detectors. For continued use of approvals dated prior to January 1, 2012, see 173.308(b)(5). B33 MC 300, MC 301, MC 302, MC 303, MC 305, MC 306, and DOT 406 cargo tanks equipped with a 1 psig normal vent used to transport gasoline must conform to Table I of this Special Provision. If one of the components, which can be a pure substance or a mixture, is classed as flammable, the chemical under pressure must be classed as flammable in Division 2.1. B59 Water-tight, sift-proof, closed-top, metal-covered hopper cars are also authorized provided that the lading is covered with a nitrogen blanket. The tank must have been designed and constructed to be capable of withstanding full vacuum. Packagings must be so constructed that explosion is not possible by reason of increased internal pressure. (5) N codes. c. The cylinders are collected and transported by a private or a contract carrier for reconditioning, reuse or disposal. A current copy of CGA pamphlet, CGA C-6 must be available at the facility servicing the life-saving appliance. For other than Class 7 or the DANGEROUS . 81 Polychlorinated biphenyl items, as defined in 40 CFR 761.3, for which specification packagings are impractical, may be packaged in non-specification packagings meeting the general packaging requirements of subparts A and B of part 173 of this subchapter. TP22 Lubricants for portable tank fittings (for example, gaskets, shut-off valves, flanges) must be oxygen compatible.